Operator Reference

projective_trans_regionT_projective_trans_regionProjectiveTransRegionProjectiveTransRegionprojective_trans_region (Operator)

projective_trans_regionT_projective_trans_regionProjectiveTransRegionProjectiveTransRegionprojective_trans_region — Apply a projective transformation to a region.

Signature

projective_trans_region(Regions : TransRegions : HomMat2D, Interpolation : )

Description

projective_trans_regionprojective_trans_regionProjectiveTransRegionProjectiveTransRegionprojective_trans_region applies the projective transformation specified by the homogeneous matrix HomMat2DHomMat2DHomMat2DhomMat2Dhom_mat_2d on the regions in RegionsRegionsRegionsregionsregions and returns the transformed regions in TransRegionsTransRegionsTransRegionstransRegionstrans_regions.

For creation and interpretation details of this matrix see also projective_trans_imageprojective_trans_imageProjectiveTransImageProjectiveTransImageprojective_trans_image.

If 'clip_region'"clip_region""clip_region""clip_region""clip_region" is set to its default value 'true'"true""true""true""true" by set_system('clip_region', 'true')set_system("clip_region", "true")SetSystem("clip_region", "true")SetSystem("clip_region", "true")set_system("clip_region", "true") or if the transformation is degenerated and thus produces infinite regions, the output region is clipped by the rectangle with upper left corner (0, 0) and lower right corner ('width'"width""width""width""width", 'height'"height""height""height""height"), where 'width'"width""width""width""width" and 'height'"height""height""height""height" are system variables (see also get_systemget_systemGetSystemGetSystemget_system). If 'clip_region'"clip_region""clip_region""clip_region""clip_region" is 'false'"false""false""false""false", the output region is not clipped except by the maximum supported coordinate size. See the “Installation Guide” for further information about coordinate range limitations. This may result in extremely memory and time intensive computations, so use with care.

Attention

The used coordinate system is the same as in affine_trans_pixelaffine_trans_pixelAffineTransPixelAffineTransPixelaffine_trans_pixel. This means that in fact not HomMat2DHomMat2DHomMat2DhomMat2Dhom_mat_2d is applied but a modified version. Therefore, applying projective_trans_regionprojective_trans_regionProjectiveTransRegionProjectiveTransRegionprojective_trans_region corresponds to the following chain of transformations, which is applied to each point of the region (input and output pixels as homogeneous vectors):

As an effect, you might get unexpected results when creating projective transformations based on coordinates that are derived from the region, e.g., by operators like area_centerarea_centerAreaCenterAreaCenterarea_center. For example, if you use this operator to calculate the center of gravity of a rotationally symmetric region and then rotate the region around this point using hom_mat2d_rotatehom_mat2d_rotateHomMat2dRotateHomMat2dRotatehom_mat2d_rotate, the resulting region will not lie on the original one. In such a case, you can compensate this effect by applying the following translations to HomMat2DHomMat2DHomMat2DhomMat2Dhom_mat_2d before using it in projective_trans_regionprojective_trans_regionProjectiveTransRegionProjectiveTransRegionprojective_trans_region:

hom_mat2d_translate(HomMat2D, 0.5, 0.5, HomMat2DTmp)hom_mat2d_translate(HomMat2D, 0.5, 0.5, HomMat2DTmp)HomMat2dTranslate(HomMat2D, 0.5, 0.5, HomMat2DTmp)HomMat2dTranslate(HomMat2D, 0.5, 0.5, HomMat2DTmp)hom_mat2d_translate(HomMat2D, 0.5, 0.5, HomMat2DTmp)

hom_mat2d_translate_local(HomMat2DTmp, -0.5, -0.5, HomMat2DAdapted)hom_mat2d_translate_local(HomMat2DTmp, -0.5, -0.5, HomMat2DAdapted)HomMat2dTranslateLocal(HomMat2DTmp, -0.5, -0.5, HomMat2DAdapted)HomMat2dTranslateLocal(HomMat2DTmp, -0.5, -0.5, HomMat2DAdapted)hom_mat2d_translate_local(HomMat2DTmp, -0.5, -0.5, HomMat2DAdapted)

projective_trans_region(Region, TransRegion, HomMat2DAdapted, 'bilinear')projective_trans_region(Region, TransRegion, HomMat2DAdapted, "bilinear")ProjectiveTransRegion(Region, TransRegion, HomMat2DAdapted, "bilinear")ProjectiveTransRegion(Region, TransRegion, HomMat2DAdapted, "bilinear")projective_trans_region(Region, TransRegion, HomMat2DAdapted, "bilinear")

For an explanation of the different 2D coordinate systems used in HALCON, see the introduction of chapter Transformations / 2D Transformations.

Execution Information

Multithreading type: reentrant (runs in parallel with non-exclusive operators).
Multithreading scope: global (may be called from any thread).
Automatically parallelized on tuple level.

Parameters

RegionsRegionsRegionsregionsregions (input_object) region(-array) → object

Input regions.

TransRegionsTransRegionsTransRegionstransRegionstrans_regions (output_object) region(-array) → object

Output regions.

HomMat2DHomMat2DHomMat2DhomMat2Dhom_mat_2d (input_control) hom_mat2d → (real)

Homogeneous projective transformation matrix.

InterpolationInterpolationInterpolationinterpolationinterpolation (input_control) string → (string)

Interpolation method for the transformation.

Default: 'bilinear' "bilinear" "bilinear" "bilinear" "bilinear"

List of values: 'bilinear'"bilinear""bilinear""bilinear""bilinear", 'nearest_neighbor'"nearest_neighbor""nearest_neighbor""nearest_neighbor""nearest_neighbor"

Possible Predecessors

vector_to_proj_hom_mat2dvector_to_proj_hom_mat2dVectorToProjHomMat2dVectorToProjHomMat2dvector_to_proj_hom_mat2d, hom_vector_to_proj_hom_mat2dhom_vector_to_proj_hom_mat2dHomVectorToProjHomMat2dHomVectorToProjHomMat2dhom_vector_to_proj_hom_mat2d, proj_match_points_ransacproj_match_points_ransacProjMatchPointsRansacProjMatchPointsRansacproj_match_points_ransac, proj_match_points_ransac_guidedproj_match_points_ransac_guidedProjMatchPointsRansacGuidedProjMatchPointsRansacGuidedproj_match_points_ransac_guided, hom_mat3d_projecthom_mat3d_projectHomMat3dProjectHomMat3dProjecthom_mat3d_project

Module

Foundation

Operators